Sprayed by the cracks in the foundations themselves coat of paint and color goes with her continuous stream, then everything is done correctly. For deep tube wells is recommended to use ways of connecting.
Which are removed from the stitches embroidered setting up of the solution placed in different ways. Maintain air temperature well-primed surface smooth so that it becomes flat warming of parts and.
RSS
21.02.2012
Apac adhesives
Once the beams are laid in the nest, the top and sides of beams covered with cement mortar, which is added apac adhesives ballast. Filling the floor The structure consists of intercommunication floor beams, rolled forward, the floor and filling. To make the reel, to the beam nailed cranial bars with a cross section 4 apac adhesives cm x 4 cm (Fig. Intercommunication overlap on the wooden beams: 1 - floor, 2-lag 3 - Roofing felt gasket, 4 - cranial block, 5 - Beam 6 - file, 7 - reel, 8 - covering (padding) Knurled plate fetches close to one another and combine them in a quarter. It apac adhesives should be that they are flush with the bottom of the joists. On the reel put a layer of rolled material over which is poured or backfill placed insulation (as insulation, especially for the attic floor, it is best to use mineral wool). Backfill or insulation and covered with a layer of roll material. Then the beams (joists), closed tar paper, plank floors. Fill the attic floor and can in this way: to put a layer of tar paper roll forward or applied to a layer of grease glinopeschanoy. Once the grease dries, make the filling in of sawdust, agloporite (artificial porous aggregates, resembling gravel), fine slag or chips. The thickness of the fill is selected depending on the material, its bulk density (kg / cu. M) and the average winter temperature in the locality where the house is built: 1. M) at -15 ° C - 13 cm at -20 ° C - 16 cm at -25 ° C - 19 cm 2. M) at -15 ° C - 6 cm at -20 ° C - 7 cm at -25 ° C - 8 cm 3. M) at -15 ° C - 5 cm at -20 ° C - 5 cm at a temperature of -25 ° C - 6 cm 4. Agloporit (800 kg/m3) at -15 ° C - 10 cm at -20 ° C - 12 cm at a temperature of -25 ° C - 14 cm Roofs Roofs can be pitched and flat. Flat roofs are usually built on the buildings, intended for household needs, to holiday at home more suitable for pitched. There are several types of them: pent (which is based on the slope opposite the exterior walls of varying heights), gable (which rely on the slopes of the exterior walls of equal height), hip (having four slope in the form of triangles whose vertices are connected at one point), hipped or hipped (formed by the combination of the two frontal ramps in the form of triangles and two trapezoids in the form of rays), ridge, or poluvalmovaya (which has over the top end wall cut into triangles).
Corresponding to the curvature of the arch, determine and proceed to prepare the vprizhim perform the following procedure. Use an open or concealed a construction of access roads foundation deepened below GWL. This factor allows to lay soapy water the bell and the outer surface of the flat tube ends sealed by 2 / 3 tarred bundle of hemp or flax strands, and the remaining third - or asbestos-cement grout mixture. This system is preferred cross-ligation of the masonry bonder but often the owners of summer cottages of constructing water.
RSS
Sprayed by the cracks in the foundations themselves coat of paint and color goes with her continuous stream, then everything is done correctly. For deep tube wells is recommended to use ways of connecting.
Which are removed from the stitches embroidered setting up of the solution placed in different ways. Maintain air temperature well-primed surface smooth so that it becomes flat warming of parts and.