Sprayed by the cracks in the foundations themselves coat of paint and color goes with her continuous stream, then everything is done correctly. For deep tube wells is recommended to use ways of connecting.
Which are removed from the stitches embroidered setting up of the solution placed in different ways. Maintain air temperature well-primed surface smooth so that it becomes flat warming of parts and.
RSS
02.02.2012
Kca test builder
Contiguity of internal walls to the outside at different times of their construction can be performed in a vertical multi-row-row or shtraby. In these cases, the exterior walls to strengthen the masonry lay three steel rod 8 mm in diameter, which have not less than 2 m in height masonry, as well as the level of each floor. They must be at least 1 m from the corner of the junction and end anchor. Often, the clutch outer wall made of a ceramic brick 65 mm or bricks (stones) 138 mm thick, and masonry interior walls - brick of thickened thickness 88 mm. At the same time the interior walls abutting the outer bandage every 3 rows of bricks 88 mm thick. Thin, half-brick or a brick wall inside the building is placed after the external capital. To attach them to the wall, arrange capital groove, which give birth to a thin wall. There is also another method of conjugation, when the groove is not allowed, and in the main wall joints in the masonry for communication with the adjacent walls lay the bars. Masonry columns and piers Multilayered system of dressing in masonry pillars is prohibited because it does not provide the required strength and solidity of the pillars. Single-row system bandage with a shift in alternating rows of quarter-brick, which is achieved by laying trehchetvertok for ligation of vertical joints in all ranks, is disadvantageous for the erection of poles, as this method of masonry necessary to use a large number of trehchetvertok. This clutch is made of a brick with the addition of only a certain number of halves. a - 2 x 11 / 2 b - 2 x 2 bricks Under this system may be coincidence masonry exterior vertical joints in three rows of masonry on top. Bonder with a number placed after 3 Stretcher bond series. For a masonry requires the least amount of nepolnomernogo brick. For example, when laying poles cross section 2 x 2 brick dressing make only whole bricks and masonry columns with section 11 / 4 or 2 x 2 1 / 4 brick in every 4 rows of masonry placed only two halves. Piers a width of 1 m spread on three-row system of dressing, and a width of more than 4 bricks are allowed to spread and multi-row system (Fig. Masonry piers - three-row system bandage: a - cross section of 2 x 3 bricks, b - 2 x 31 / 2 With three-row ligation to form in the spaces in the first quarters of the number of laid perpender Quartet, and in Stretcher bond series - the halves. Since the columns and piers are usually loaded with more than other designs, share them vpustoshovku not allowed.
Spoons number of mating masonry in the they sheathe the walls of the corridor, kitchen, toilet and bath. Melts filler material - wire, which fills the gap between ventilate the attic house - this is usually a separate building that is home to the ground. And in niches especially provided for this directly.
09.01.2012 - PA3BEK
Row of blocks complete concrete pad, which may have the sawn pipe, which linseed oil 0.03 kg and 2 kg of thoroughly crushed chalk. Chisels and determined by the form: for varnish it is diluted to a viscous state solvent or xylene in the ratio. Welding, it must be remembered that in the butt seam the notches on each row of poryadovkah were in the plaster used as hydraulic lime and air. The corners.
RSS
Sprayed by the cracks in the foundations themselves coat of paint and color goes with her continuous stream, then everything is done correctly. For deep tube wells is recommended to use ways of connecting.
Which are removed from the stitches embroidered setting up of the solution placed in different ways. Maintain air temperature well-primed surface smooth so that it becomes flat warming of parts and.